Save Money: Make Your Vents New Again

There’s always something to do “At Koko’s Place”. I have a project list that seems to never end. One of those projects was addressing the vents; floor vents, wall vents, ceiling vents. I’d stare at the chipped-rusted vents daily…not out of being neurotic, but because I’d see them at least twice a day vacuuming. I knew I’d eventually get to it. What I didn’t know was that it’d take me ten years to do so!

Here’s what I did to make my vents new again. Oh, before I continue on the how, I wanted to mention that I looked into buying new vents. There were white ones, and metallic ones, and the same brown colored ones that mine were. The prices ranged from $8 to $15 dollars each. I have 24 of them and well that’s a lot of money. Also, my vents weren’t damaged, they were just chipped and rusty. My conscience wouldn’t allow me to toss them. What else could I do? The obvious answer was to paint them, so I did.

Now…here’s what I did…

IMG_5925

Sparing you a ton of pictures…this is an example of what they all look like.

If you are a DIY’er, I’m sure you’ve researched how to remove rust. There are many ways to do so. One of them is soda pop method. I thought I’d give it a try. I mean, if it saved me from having to sand each one by hand, I’m in!

IMG_4215

I don’t drink soda, but I happen to have been given a gift basket with this in it.

IMG_4218 (1)

Supposedly you let the object sit in the cola and it eats away the rust.

IMG_4279 (2)

This is what it looked like days later. It did eat off some of the rust, but not all, and the metal seemed to have bubbled, so sanding was still a must. I decided I wouldn’t be continuing this cola method.

IMG_4282 (1)

I lightly sanded all over the vent and took more time to sand the rust places clean.

IMG_4213

For the slots…I wrapped sand paper around a tongue depressor/wooden stick…anything flat to get between the slots will work…butter knife…ruler…piece of cardboard…

After I sanded, I washed the vents with soap, and rinsed, and dried them well. I set them in front of a fan to make sure they dried thoroughly.

Oh, I forgot to mention that before I did all of that, I went to my local Home Depot to get the paint. I didn’t know what color I wanted to spray them, I just knew I didn’t care for the color they were.

IMG_6079

My paint guy suggested this type of paint. He said this had great coverage and would be durable. I needed durable since most of the vents are on the floor. He said this paint would be a great choice. I was stoked that it was a paint and primer in one! I like the metallic bits in the paint. Helps to hide imperfections in the metal too! Win-win.

IMG_5922 (1)

I let my paint guy choose the color. I’ve been getting his advice on paint for a decade and he hasn’t let me down! It glitters! Shiny! Swoon!

IMG_6089 (1)

This pic was taken during the day. I love the color!

IMG_5924.jpg

Before…(Vent from downstairs bathroom).

IMG_6088 (1)

After! (Vent from living room).

What do you think of the before and after?

What I took away from this project: 1. You can’t skip good old fashion sanding. I don’t enjoy doing it, it’s just one of those things you can’t get away from. So, unless you know of an easier way of getting rid of rust… 2. A good paint is essential for a good outcome.

Pros on this Rust-Oleum Universal Advance Metallic Spray paint:

1. As I mentioned above, the metallic hides flaws and if there were no flaws, I’d still use it because the metallic feature is just so pretty and just so cool, don’t you think?!

2. I like the spray nozzle. It’s comfortable and simple to use. Just shake well, point and go at it! I was concerned about getting to the many slots and angles of the vents, but I found that the type of nozzle on this particular spray can, really handled the job well. No sore finger (if you’ve done a lot of spray painting, you know what I mean). I found doing short bursts the best way to get it covered. I did three coats and made sure that I allowed it to dry to the touch in between coats. It was a nice warm day and it was dry to the touch in about 15 minutes, but I waited an hour. After the last coat was on and dried to the touch, I stored the vents in the garage for a week to make sure they were fully cured before installing them.

3. The finish of the paint is really smooth.

4. I like how fast the paint dried (to the touch).

5. As for durability, it’s holding up super well. I vacuum right over them at least twice a day.

Cons on this Rust-Oleum Universal Advance Metallic Spray paint…

1. This isn’t a really a con, but it’s the only thing I can think of…having to take off paint with mineral spirits. I know, it’s not really a con. This paint is oil based and as you know, oil based needs mineral spirits to take off.

I’m thrilled with the outcome. This project was easy… time-consuming (because I waited several days for a good hard cure), but easy. This saved me money too (Insert cheer here*).

Look out rusted shower curtain rod…you’re next! Rust-Oleum Universal Metallic Advanced Paint and Primer in One is a paint I will use again.

I don’t regret the color, but as the project continued, I was thinking about other colors and it could be a fun way to add a “pop” of color; like orange, or turquoise, or rose gold… If you do this project, a “pop” of color could be super awesome! 🙂

If you have vents that need a face-lift, this could be a fab solution for you. Thank you for reading!

✿ Peace, Koko ✿

 

 

 

 

Advertisements

DIY Shelves Ikea Style

 

IMG_5452

I’m super excited about the new shelves in my home! There were some minor hiccups along the way, (isn’t that how it usually is with DIY… you experiment, try new things?) even with the “ack” moments, I’m really happy with the way it all turned out. This is how it went down…or up?…

IMG_9126

I tried to make my own stain using the steel wool method. Notice the word tried? I want to give this DIY stain another go. I believe my mistake was letting this mixture sit too long. Thus the strong rust color rather than the weathered gray I was going for.

IMG_9130 (1)

1. Fine steel wool in a glass jar  2. Pour white vinegar to cover steel wool (about 2 cups)  3. Let sit for a few days  4. Stain is made (again, I think I let mine sit too long)

IMG_4160

These brackets are from Ikea. I bought them about 10 years ago. They were light pine, lovely as is, but I wanted a weathered look. The second bracket from the left was after one coat and the third bracket was after a second coat. Neither color was anywhere near the weathered gray I was going for.

IMG_4157

I found the stain didn’t go on evenly even though I applied it evenly. Perhaps it was because I didn’t use a wood conditioner.

IMG_4156

I had hoped with a third coat the color would even out somewhat (and hoping the color would gray out as they dried…), but that was not the case. As I mentioned above, the color came out a “rust” color instead of the weathered gray I was hoping to achieve. At this point I was not in a full-blown panic, but more like “ack”! I’d been waiting for the right time and place to use these and now I’ve ruined them! What do I do now?

So… I got out my trusty DeWALT palm sander and went at the brackets. I didn’t sand them down to bare wood as I still wanted the weathered look and decided a whitewashed technique could be just what these brackets needed. You can see the whitewashed technique here.

IMG_1935 (1)

I wanted to mention how I hang stuff on my walls. TAPE. I use tape to “see” what the finished look will look like. You will see in future posts that the artwork is hung different from what is taped here (hence the beauty of using tape. See it before the nails go in.) I also changed the color of the walls in this room. The clock stayed in the same spot and so did the shelves. 🙂 I moved the cat house you see in the corner of the picture to the hall upstairs. I’ve noticed the cats scratch at it way more up there and it seems to be a great spot for them to go to when they need some quiet time. (see the cat post here) The lamp was moved to another room. You can see the lamp shade project here. Following At Koko’s Place you will see that things rarely stay in the same place for long!

IMG_3420

The boards I used for the shelves used to be one of two huge bookcases. My awesome husband took them apart for me and the boards sat in the garage where they awaited what their new life would be. Picture them stained the darkest brown color you see here. I sanded them, leaving both the natural wood color and some of the brown stain, knowing I would whitewash the boards using the technique I did on the dresser turned desk here.

IMG_3421

In making the bookcases, I countersunk screws… In making shelves, I didn’t want them to show. I then cut four boards down to 40 1/2 inches long using my DeWALT jig saw and then sanded the edges. 

IMG_3422

Patch away I did. There was a lot of patching to do! After patching, I sanded it all flat.

IMG_2853

Dark gray walls now! The rack of plants I move around to follow the sun. And spoiled pets…the reason we bought sofas. 😉

IMG_4557

Taped the walls again after the new color went on. Frog tape was used this time instead of Scotch Blue. The headlamp was because I decided to hang the shelves around midnight and I didn’t have adequate lighting in the room at the time. What? I know I’m not the only one that does projects at odd hours 😉

IMG_4560

I used the level as I taped the lines. It made the job easier for me. I didn’t have studs where I needed them to be, so I used wall anchors. Best invention. See them in this project here.

IMG_4561

Four down, four to go!

IMG_4562

Even though I pre-leveled, I still would check the level as I went along. I also made sure the brackets were in a straight line.

IMG_4563

All done! Now to add the boards.

IMG_5131

*Insert happy squeal here!

IMG_4989

Plants bought from Trader Joe’s, Home Depot, and Costco. Owl from TJMaxx. Buddha, can’t remember, I’ve had him for a long time.

I lived with the blue, then the green tapes for a bit. Over the course of a few weeks, I moved the tapes from three shelves to four and played with the spacing. I tried to picture what I would have on the shelves and how tall I envisioned the plants to grow. Since I love greenery, I knew I wanted more space to put them so that was why I added the fourth shelf. And I am happy I did!

Thank you so much for reading. As always, I appreciate YOU! Have a beautiful day!

❀Be well and just love! Peace, Koko❀

 

DIY Garden Gate

I hope you enjoy the video as much as I enjoyed building the gates. I share what I do/build to show that you too can do it! The garden gate was a plan in my head and thankfully it came out just as I pictured. This really was an easy build. I am NOT a skilled woodworker, so when I say you can do this… I really believe that! You can see past posts on gates I’ve done here and here.

*You may have to adjust your volume. I apologize ahead of time if it’s loud.* The music is by my daughter. She wrote the lyrics and music and sings. The song has special meaning to her. I hope you enjoy it.

Peace be with you today and everyday! Like the song’s title “Stand”, I hope you take a stand to be happy, healthy, to love big, show kindness, be the one to reach out to someone, to care, and most of all to love yourself. Koko

 

 

 

DIY Easy Garden Gate How To

Garden gate…two down, two to go!

Here’s my second gate.  This one took me less time to build than the last one.  Progress! (about three hours counting painting) This gate is wider than the first one, by over a foot,  so I had to build into it a little more support.  I also added an extra hinge in the center.  I don’t know if it was necessary, however five years from now I don’t want the gate wobbling or sagging.  (Though five years from now it would be nice to be living near the beach again…oh how I miss the ocean.)

Measured out the width of gate and where I wanted the bottom and top slat to be.

Measured out the width of gate and where I wanted the bottom and top slat to be.

Laid boards out and measured out the distance apart I wanted.

Laid boards out and measured out the distance apart I wanted.

Screwed all boards and drew a curved line at top of gate. I cut it out with a jig saw.

Screwed all boards and drew a curved line at top of gate. I cut it out with a jig saw.

Added cross pieces for more stability.

Added cross pieces for more stability.

Finished and painted. That's my garden behind that gate! One of my favorite crepe myrtle trees on the left. Love the blossoms!

Finished and painted. That’s my garden behind that gate! One of my favorite crepe myrtle trees on the left. Love the blossoms!

Do you enjoy building things? I’d love to hear about a project you’ve done! Thank you so much for taking the time out of your day to read. I hope this finds you happy and healthy and that you are doing something that makes you smile. Peace, Koko