DIY Shelves Ikea Style

 

IMG_5452

I’m super excited about the new shelves in my home! There were some minor hiccups along the way, (isn’t that how it usually is with DIY… you experiment, try new things?) even with the “ack” moments, I’m really happy with the way it all turned out. This is how it went down…or up?…

IMG_9126

I tried to make my own stain using the steel wool method. Notice the word tried? I want to give this DIY stain another go. I believe my mistake was letting this mixture sit too long. Thus the strong rust color rather than the weathered gray I was going for.

IMG_9130 (1)

1. Fine steel wool in a glass jar Β 2. Pour white vinegar to cover steel wool (about 2 cups) Β 3. Let sit for a few days Β 4. Stain is made (again, I think I let mine sit too long)

IMG_4160

These brackets are from Ikea. I bought them about 10 years ago. They were light pine, lovely as is, but I wanted a weathered look. The second bracket from the left was after one coat and the third bracket was after a second coat. Neither color was anywhere near the weathered gray I was going for.

IMG_4157

I found the stain didn’t go on evenly even though I applied it evenly. Perhaps it was because I didn’t use a wood conditioner.

IMG_4156

I had hoped with a third coat the color would even out somewhat (and hoping the color would gray out as they dried…), but that was not the case. As I mentioned above, the color came out a “rust” color instead of the weathered gray I was hoping to achieve. At this point I was not in a full-blown panic, but more like “ack”! I’d been waiting for the right time and place to use these and now I’ve ruined them! What do I do now?

So… I got out my trusty DeWALTΒ palm sander and went at the brackets. I didn’t sand them down to bare wood as I still wanted the weathered look and decided a whitewashed technique could be just what these brackets needed. You can see the whitewashed technique here.

IMG_1935 (1)

I wanted to mention how I hang stuff on my walls. TAPE. I use tape to “see” what the finished look will look like. You will see in future posts that the artwork is hung different from what is taped here (hence the beauty of using tape. See it before the nails go in.) I also changed the color of the walls in this room. The clock stayed in the same spot and so did the shelves. πŸ™‚ I moved the cat house you see in the corner of the picture to the hall upstairs. I’ve noticed the cats scratch at it way more up there and it seems to be a great spot for them to go to when they need some quiet time. (see the cat post here) The lamp was moved to another room. You can see the lamp shade project here. Following At Koko’s PlaceΒ you will see that things rarely stay in the same place for long!

IMG_3420

The boards I used for the shelves used to be one of two huge bookcases. My awesome husband took them apart for me and the boards sat in the garage where they awaited what their new life would be. Picture them stained the darkest brown color you see here. I sanded them, leaving both the natural wood color and some of the brown stain, knowing I would whitewash the boards using the technique I did on the dresser turned desk here.

IMG_3421

In making the bookcases, I countersunk screws… In making shelves, I didn’t want them to show. I then cut four boards down to 40 1/2 inches long using my DeWALT jig saw and then sanded the edges.Β 

IMG_3422

Patch away I did. There was a lot of patching to do! After patching, I sanded it all flat.

IMG_2853

Dark gray walls now! The rack of plants I move around to follow the sun. And spoiled pets…the reason we bought sofas. πŸ˜‰

IMG_4557

Taped the walls again after the new color went on. Frog tape was used this time instead of Scotch Blue. The headlamp was because I decided to hang the shelves around midnight and I didn’t have adequate lighting in the room at the time. What? I know I’m not the only one that does projects at odd hours πŸ˜‰

IMG_4560

I used the level as I taped the lines. It made the job easier for me. I didn’t have studs where I needed them to be, so I used wall anchors. Best invention. See them in this project here.

IMG_4561

Four down, four to go!

IMG_4562

Even though I pre-leveled, I still would check the level as I went along. I also made sure the brackets were in a straight line.

IMG_4563

All done! Now to add the boards.

IMG_5131

*Insert happy squeal here!

IMG_4989

Plants bought from Trader Joe’s, Home Depot, and Costco. Owl from TJMaxx. Buddha, can’t remember, I’ve had him for a long time.

I lived with the blue, then the green tapes for a bit. Over the course of a few weeks, I moved the tapes from three shelves to four and played with the spacing. I tried to picture what I would have on the shelves and how tall I envisioned the plants to grow. Since I love greenery, I knew I wanted more space to put them so that was why I added the fourth shelf. And I am happy I did!

Thank you so much for reading. As always, I appreciate YOU! Have a beautiful day!

❀Be well and just love! Peace, Koko❀

 

DIY Magnetic Message Board

IMG_9104

Your refrigerator is the perfect spot to post a note to remind you of something. In my home it’s one of the most opened door; which means papers/coupons, cards, notes can go flying off. My kitchen isn’t wide where the fridge sits and often times the “stuff” that is on the front of the fridge gets knocked off. My solution was to create a message board near enough where we could still see it, but out of the way from walking traffic. Remember, if I can, you can! Let’s get started…

Materials needed:

Sheet metal

Screws

Rubber grommets

Tools:

Screw driver or drill

Drill bits to pre-drill

Level

IMG_9103

I purchased a piece of sheet metal. I was prepared to cut the sheet metal to size using tin snips, however I got lucky that the area I decided to put the sheet metal is a size that the hardware store readily stocks.

I had several ideas for how I was going to hang the sheet metal. If I had to cut it using tin snips I knew the cut edge wouldn’t be smooth and I was going to “hide” it using molding to “frame” the sheet metal. That would have still looked nice, but I decided to use only screws and grommets. I like the clean/modern look of how it came out.

IMG_9106

I predrilled where I wanted the screws to go. Added the rubber grommet and screwed the screw in.

IMG_9109

IMG_9110

There you have it! A message board that’s still accessible without clogging up the front of the refrigerator.

It was a quick and easy project that anyone with any skill level can do. If you are using tin snips; remember to wear gloves. And always protect your eyes!

I am on the go constantly! Often times I wish I could duplicate myself! I may not post weekly (I’m a bit more active on twitter and instagram as I can post pics while in between my crazy busy life…follow me!), but I do read your posts! I enjoy every one of them. I read your blogs every chance I get and get inspired daily from them. Your posts make me smile, think, energize me, and carry me when I am down. Just wanted you to know I appreciate you and the time you take to write!

Hope you had a wonderful Valentines. I got my guy this:

(Evan-the-dog adorably photo-bombing!)

Image

Who am I kidding…I probably will be on it more than him! Teehee πŸ˜‰ He actually loves it! After 25 Valentines you have to get creative.

Be kind to yourself and to others! Have a beautiful day!

Peace and hugs, Koko πŸ™‚