Save Money: Make Your Vents New Again

There’s always something to do “At Koko’s Place”. I have a project list that seems to never end. One of those projects was addressing the vents; floor vents, wall vents, ceiling vents. I’d stare at the chipped-rusted vents daily…not out of being neurotic, but because I’d see them at least twice a day vacuuming. I knew I’d eventually get to it. What I didn’t know was that it’d take me ten years to do so!

Here’s what I did to make my vents new again. Oh, before I continue on the how, I wanted to mention that I looked into buying new vents. There were white ones, and metallic ones, and the same brown colored ones that mine were. The prices ranged from $8 to $15 dollars each. I have 24 of them and well that’s a lot of money. Also, my vents weren’t damaged, they were just chipped and rusty. My conscience wouldn’t allow me to toss them. What else could I do? The obvious answer was to paint them, so I did.

Now…here’s what I did…

IMG_5925

Sparing you a ton of pictures…this is an example of what they all look like.

If you are a DIY’er, I’m sure you’ve researched how to remove rust. There are many ways to do so. One of them is soda pop method. I thought I’d give it a try. I mean, if it saved me from having to sand each one by hand, I’m in!

IMG_4215

I don’t drink soda, but I happen to have been given a gift basket with this in it.

IMG_4218 (1)

Supposedly you let the object sit in the cola and it eats away the rust.

IMG_4279 (2)

This is what it looked like days later. It did eat off some of the rust, but not all, and the metal seemed to have bubbled, so sanding was still a must. I decided I wouldn’t be continuing this cola method.

IMG_4282 (1)

I lightly sanded all over the vent and took more time to sand the rust places clean.

IMG_4213

For the slots…I wrapped sand paper around a tongue depressor/wooden stick…anything flat to get between the slots will work…butter knife…ruler…piece of cardboard…

After I sanded, I washed the vents with soap, and rinsed, and dried them well. I set them in front of a fan to make sure they dried thoroughly.

Oh, I forgot to mention that before I did all of that, I went to my local Home Depotย to get the paint. I didn’t know what color I wanted to spray them, I just knew I didn’t care for the color they were.

IMG_6079

My paint guy suggested this type of paint. He said this had great coverage and would be durable. I needed durable since most of the vents are on the floor. He said this paint would be a great choice. I was stoked that it was a paint and primer in one! I like the metallic bits in the paint. Helps to hide imperfections in the metal too! Win-win.

IMG_5922 (1)

I let my paint guy choose the color. I’ve been getting his advice on paint for a decade and he hasn’t let me down! It glitters! Shiny! Swoon!

IMG_6089 (1)

This pic was taken during the day. I love the color!

IMG_5924.jpg

Before…(Vent from downstairs bathroom).

IMG_6088 (1)

After! (Vent from living room).

What do you think of the before and after?

What I took away from this project: 1. You can’t skip good old fashion sanding. I don’t enjoy doing it, it’s just one of those things you can’t get away from. So, unless you know of an easier way of getting rid of rust… 2. A good paint is essential for a good outcome.

Pros on this Rust-Oleum Universal Advance Metallic Spray paint:

1. As I mentioned above, the metallic hides flaws and if there were no flaws, I’d still use it because the metallic feature is just so pretty and just so cool, don’t you think?!

2. I like the spray nozzle. It’s comfortable and simple to use. Just shake well, point and go at it! I was concerned about getting to the many slots and angles of the vents, but I found that the type of nozzle on this particular spray can, really handled the job well. No sore finger (if you’ve done a lot of spray painting, you know what I mean). I found doing short bursts the best way to get it covered. I did three coats and made sure that I allowed it to dry to the touch in between coats. It was a nice warm day and it was dry to the touch in about 15 minutes, but I waited an hour. After the last coat was on and dried to the touch, I stored the vents in the garage for a week to make sure they were fully cured before installing them.

3. The finish of the paint is really smooth.

4. I like how fast the paint dried (to the touch).

5. As for durability, it’s holding up super well. I vacuum right over them at least twice a day.

Cons on this Rust-Oleum Universal Advance Metallic Spray paint…

1. This isn’t a really a con, but it’s the only thing I can think of…having to take off paint with mineral spirits. I know, it’s not really a con. This paint is oil based and as you know, oil based needs mineral spirits to take off.

I’m thrilled with the outcome. This project was easy… time-consuming (because I waited several days for a good hard cure), but easy. This saved me money too (Insert cheer here*).

Look out rusted shower curtain rod…you’re next! Rust-Oleum Universal Metallic Advanced Paint and Primer in One is a paint I will use again.

I don’t regret the color, but as the project continued, I was thinking about other colors and it could be a fun way to add a “pop” of color; like orange, or turquoise, or rose gold… If you do this project, a “pop” of color could be super awesome! ๐Ÿ™‚

If you have vents that need a face-lift, this could be a fab solution for you. Thank you for reading!

โœฟ Peace, Koko โœฟ

 

 

 

 

Advertisements

DIY Magnetic Message Board

IMG_9104

Your refrigerator is the perfect spot to post a note to remind you of something. In my home it’s one of the most opened door; which means papers/coupons, cards, notes can go flying off. My kitchen isn’t wide where the fridge sits and often times the “stuff” that is on the front of the fridge gets knocked off. My solution was to create a message board near enough where we could still see it, but out of the way from walking traffic. Remember, if I can, you can! Let’s get started…

Materials needed:

Sheet metal

Screws

Rubber grommets

Tools:

Screw driver or drill

Drill bits to pre-drill

Level

IMG_9103

I purchased a piece of sheet metal. I was prepared to cut the sheet metal to size using tin snips, however I got lucky that the area I decided to put the sheet metal is a size that the hardware store readily stocks.

I had several ideas for how I was going to hang the sheet metal. If I had to cut it using tin snips I knew the cut edge wouldn’t be smooth and I was going to “hide” it using molding to “frame” the sheet metal. That would have still looked nice, but I decided to use only screws and grommets. I like the clean/modern look of how it came out.

IMG_9106

I predrilled where I wanted the screws to go. Added the rubber grommet and screwed the screw in.

IMG_9109

IMG_9110

There you have it! A message board that’s still accessible without clogging up the front of the refrigerator.

It was a quick and easy project that anyone with any skill level can do. If you are using tin snips; remember to wear gloves. And always protect your eyes!

I am on the go constantly! Often times I wish I could duplicate myself! I may not post weekly (I’m a bit more active on twitter and instagram as I can post pics while in between my crazy busy life…follow me!), but I do read your posts! I enjoy every one of them. I read your blogs every chance I get and get inspired daily from them. Your posts make me smile, think, energize me, and carry me when I am down. Just wanted you to know I appreciate you and the time you take to write!

Hope you had a wonderful Valentines. I got my guy this:

(Evan-the-dog adorably photo-bombing!)

Image

Who am I kidding…I probably will be on it more than him! Teehee ๐Ÿ˜‰ He actually loves it! After 25 Valentines you have to get creative.

Be kind to yourself and to others! Have a beautiful day!

Peace and hugs, Koko ๐Ÿ™‚